A method for rapidly evaluating reliability and predicting remaining useful life using two-dimensional convolutional neural network with signal conversion

Journal of Mechanical Science and Technology - Real-time monitoring and rapid evaluation of bearing operating conditions, especially for the reliability evaluation and remaining useful life (RUL)...     

离子侵蚀对再生混凝土多重界面区微观形貌影响

为了研究离子侵蚀对再生混凝土多重界面过渡区的影响,借助SEM和EDS,以Ca元素和Si元素为特征元素进行面扫描,实现了对骨料和砂浆基体的区分,发现了经NaCl溶液和Na2SO4溶液浸泡60 d后的再生混凝土界面过渡区趋于疏松;以S元素和Cl元素为示踪元素,观察到其在界面区的富集,证明了界面过渡区是离子侵蚀的主要通道;浸泡60 d后界面区显微硬度分别下降约70％和20％,界面过渡区宽度分别增加约50％和20％.研究实现了对离子侵蚀后再生混凝土界面过渡区位置和范围的界定,且表现出与显微硬度结果的一致性.     

焊缝表面缺陷激光扫描三维重构测量

为检测工件焊缝表面缺陷，采用点激光位移传感测距法和数据拟合技术进行焊缝表面缺陷检测试验研究. 首先采集缺陷表面轮廓数据点，利用高斯滤波对原始数据降噪处理. 再对处理后的数据点进行Delaunay三角剖分，使散乱点连接并结合其空间坐标重构出缺陷的三维模型. 结果表明，基于点激光位移传感测距技术及焊缝表面缺陷三维重构方法可以准确判断焊缝成形情况.     

高落差粉尘扩散规律和分布特征

高溜井放矿过程中会形成强大的冲击气流引起粉尘扩散，造成严重的井下环境污染，对其进行有效治理一直是井下通风除尘的工作重心，本工作利用相似实验和数值模拟相结合的方式探究溜井放矿过程中粉尘的扩散规律和分布特征。通过改变放矿质量、矿石粒径、溜井密闭程度、含水率等因素测试不同条件下气流大小和粉尘浓度分布，并利用CFD-DPM耦合方法模拟卸矿过程中的气?固两相流，研究气流和粉尘浓度时空分布特征。结果表明，最大粉尘浓度和风速随放矿质量增加而上升，随颗粒粒径和溜井密闭程度增大而降低，且含水率越大，粉尘浓度越小，风速无明显变化，在放矿过程中矿石颗粒之间碰撞占主导作用，颗粒流呈横向分布。     

Preparation of CaO granules using the granulation method

ABSTRACT

Improving the hydration resistance of CaO particle in manufacturing and application of free CaO-containing materials has practical significance. In this study, CaO granules was made from Ca(OH)₂ particles, which were fabricated by the granulation method. The results showed that the hydration resistance of the CaO granules which was prepared under 1700?r?min^?1 was the best, the CaO granules was sintered well in calcination process, the shell of CaO granules was relatively dense, which improves the hydration resistance of CaO granules, and the rate of hydration weight increment was 0.58% after placed in the air for 20 days under a temperature of 10–14°C and a relative humidity of 57–81%.     

磁絮凝强化技术处理厌氧消化污泥脱水液

为满足后续生物处理单元对固体悬浮物（SS）和铁浓度的进水要求，采用磁絮凝强化技术对厌氧消化污泥脱水液进行预处理。通过正交试验和单因素试验，本文考察了混凝水力条件、聚合氯化铝（PAC）投加量、聚丙烯酰胺（PAM）投加量、磁粉投加量及药剂投加顺序对磁絮凝效果的影响。试验结果表明：磁絮凝强化技术在快搅300r/min（2min）、慢搅100r/min（15min）、静置10min时，依次投加磁粉（40mg/L）、PAC（30mg/L）、PAM（4mg/L）时处理效果最好。在此运行条件下，SS和Fe³⁺去除率分别为97.61%、98.24%、絮凝指数（FI值）取得最大值、zeta电位绝对值最小，絮凝效果最佳。与对照相比，磁絮凝强化技术对SS和Fe³⁺去除率分别可提高3.70%和10.82%，同时絮体最大沉降速度可提高33%。磁絮凝技术处理后的出水不仅可以满足后续生物处理单元对SS和铁浓度的要求，还可以有效提高磁絮凝体的沉降速度，减小沉淀时间，具有较好的实用价值。     

Development of Core-Shell Nanoparticle Drug Delivery Systems Based on Biomimetic Mineralization

Among various drug-delivery systems, core-shell nanoparticles have many advantages. Inspired by nature, biomimetic synthesis has emerged as a new strategy for making core-shell nanoparticles in recent years. Biomimetic mineralization is the process by which living organisms produce minerals based on biomolecule templating that leads to the formation of hierarchically structured organic–inorganic materials. In this minireview, we mainly focus on the synthesis of core-shell nanoparticle drug-delivery systems by biomimetic mineralization. We review various biomimetic mineralization methods for fabricating core-shell nanoparticles including silica-based, calcium-based and other nanoparticles, and their applications in drug delivery. We also summarize strategies for drug loading in the biomolecule-mineralized core-shell NPs. Current challenges and future directions are also discussed.     

基于热电效应的高效环控系统

部分空间科学实验对环境温度有较高的要求，环境温度高于或低于空间科学系统能够提供的热沉温度，需要有可靠有效的加温降温处理措施。使用可靠性强的热电制冷片作为制冷制热方式和气液换热器二次换热来实现环境温度控制的需求，并对不同流体温度制冷制热效果进行分析，结果表明流体温度和目标温度差越小，热电制冷制热的效果越好。在环境温度制冷工况中，热电单元数量随电流增加先减少后增加，在制热工况中则单调递减，设计中需按照制冷工况进行热电单元数量的确定。当流体温度接近制冷制热的目标温度时，会出现整个系统总效率优于热电系统效率的区间。通过对热电单元和气液换热器的组合系统的性能计算，提供一种适于热电环控系统的计算方法和部件选型思路，对空间站环控系统的设计有重要参考意义。